Home  > Haida Products  > Environmental Test Chamber  > Climatic Test Chambers  >  thermal shock environmental test chamber
Haida Equiment Manufacturer

Haida Equiment Manufacturer has more than 15 years experience for test equipment...

thermal shock environmental test chamber

thermal shock environmental test chamber

15 days after order.
Each set protected with resin fiber and PP film, then put into Strong wooden case with operation manual and video inside.
L/C, D/P, T/T

Thermal shock environmental test chamber

 Thermal Shock Test Chamber Video                       Thermal Shock Test chamber Brochure

Product usage:

Thermal shock environmental test chamber is used to test the material structure or composite materials, in an instant by the very high temperature and very low temperature can withstand the extent of continuous environment in order to test in the shortest time of its thermal expansion and contraction caused by chemical changes or physical hurt.

thermal shock environmental test chamber  be equipped with a PID auto calculation control,safety device.so shermal shock chamber can program control the change tempereture of hot chamber and cool chamber during cycles testing.

that means this thermal shock environmental test chamber can test the material's chemical change or physics change by expansion and contraction within short time.and tis type environmental testing chamebr can application to metal, plastic, rubber, electronic etc materials and can be used for product improvement's reference.

Corresponding standard:
1 GB/T2423.1-1989 low-temperature testing method
2 GB/T2423.2-1989 high-temperature testing method
3 GB/T2423.22-1989  change temperature test
4 GJB150.5-86  temperature impact test
5 GJB360.7-87  temperature impact test
6 GJB367.2-87 405 temperature impact test


  1. Perfect appearance and easy to operate.

  2. Imported LCD English microcomputer temperature controller, with high memory capacity, can save 100 programs, max 9999 cycles, each cycle max time 999hrs.

  3. Two chamber structures, high temperature chamber and low temperature chamber, control automatically, stay and switch time adjustable.

  4. Perfect protection alarm functions: short-circuits, Leakage, over temperature of work chamber; compressor over pressure, over load, short water…

  5. Control interface will display alarm reason and provide check methods, machine has emergency stop button.

  6. Cold and hot shock temperature recover within1 minute, which complies with MTL, IEC, JIS, GJB and other international standards.


Main parameters:



Test method

Pneumatic operated door switch, two chambers

Basket internal dimension

320Wx230Dx250Hmm (20L)

External chamber dimension


High temperature range

Room temperature +175℃

Low temperature range

Room temperature -50℃

Testing time

Maximum 1000 cycles, 30 minutes for each one


Do defrost in every 20 cycles

Temperature deviation


Lifting switch time

≤10 seconds

Test hole for cable routing

Diameter 50mm on the left of chamber attach a silicone plug

External chamber material

High quality electrolytic steel plate spray with powder, antirust

Internal material

SUS#304 stainless steel

Thermal insulation material

High quality superfine glass fiber


R404A / R23

Cooling method

Water cooling

Power supply

Three phase, 380V, 50Hz



High temperature chamber:

1, Including three parts: heater, draught fan and air duct valve

2, Draught fan cyclically stirs hot air through heater

3, The basket with testing product drive to high temperature range when doing high temperature impact test.


Low temperature chamber:

1, Including four parts: evaporator, energy storage piece, draught fan and air duct valve

2, Draught fan cyclically stirs cold air through evaporator and energy storage piece.

3, The basket with testing product drive to low temperature range when doing low temperature impact test.


Drive device:

Pneumatic cylinder: drive basket with testing product to high and low temperature chamber

Air compressor: Provide the compressed air for driving pneumatic door (supplied by buyer)


Refrigerating device:

Cooling system: complex overlapping efficient cryogenic loop system

Compressor: Bock compressor

Refrigerant: environmental protection refrigerant R23/R404A

Condensation: Stainless steel welded plate heat exchanger



Operate interface: 6" color PLC controller, touch screen

Program memory capacity: 100 groups (modify by operator)

Setting range: Time: 1 minute ~ 99 hour 59 minute, cycles: 1~ 9999cycles

Resolution: temperature: 0.01 ℃

Input: T thermocouple

Control method: PID auto calculation control


Additional functions:

Timer, over temperature and power failure protection, alarm, record test curve, emergency stop, display test time

Standard configuration: indication lamp of test chamber, time meter, test hole for wire routing, 6pcs castor, 4pcs adjust wheel.


Safety device:

Power overload protection                                 

Leakage protection

Control circuit overload protection

Short-circuit protection

Compressor overload protection

Ground protection

Over temperature protection

Audible and visual alarm

Optional Accessories:

Computer interface RS232 

External paperless recorder with color display (Yokogawa six-channel)

Factory calibration certificate  



Start-up and training

Start-up, training and instrument calibration for the above equipments

Start-up of the system by a qualified service technician

Training session on the operation and maintenance of the system

Calibration with certificate 

(contact capacity: AC 250V, 2Am)

Leave a Message


Loading verification code...

Please complete verification first

Chat Online
Chat Online
Chat Online inputting...